Gable roof
A plain gable with common rafters each side of a ridge board. Cutting templates for the birdsmouth and plumb cuts are in the common rafter calculator.
Slope as
Overhang measured
Rafter
Rafter centers
Birdsmouth by
Common rafter
- Roof angle6:12 pitch
- 26.57°
- Runhalf the building width, to the ridge centre
- 12' 0"
- Rise
- 6' 0"
- Ridge shorteningtaken off each rafter at the ridge, along the rafter
- 13/16"
- Line lengthridge cut to the outer wall plumb line, shortened for the ridge
- 13' 4 3/16"
- Tail length2' 0" level overhang
- 2' 2 13/16"
- Overall lengthlong point to long point, shortened for the ridge
- 15' 7"
- Plumb cutsaw miter from square · length of the cut
- 26.57° · 8 1/8"
- Seat cut
- 63.43° · 3 1/2"
- Height above plate
- 6 3/8"
- Ridge top above plateridge board at least 8 1/8" deep to carry the full plumb cut
- 6' 6 3/8"
- Stock lengtheach rafter cut from this, to the next 2 ft
- 16' 0"
Whole roof
- Rafters31 a side at 16" centers, including both end rafters
- 62
- Ridge lengthbuilding length plus 1' 0" rake overhang each end
- 42' 0"
- Fasciaboth eaves
- 84' 0"
- Slope lengtheave to ridge along the roof, per side
- 15' 7 13/16"
- Roof area657.40 sq ft per side
- 1314.81 sq ft
- Sheathing sheets24 per side, 4' 0" × 8' 0" sheets, no waste allowance
- 48
- Rafter lumber62 × 16' 0" 2x8
- 899.0 bft
- Rafter costat $800 per 1000 bft
- $719.20
Cross section
Gable roof section
Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.
Rafter plan
Rafter layout
Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.
| # | Mark | Position |
|---|---|---|
| 1 | end | 0" |
| 2 | 1' 3 1/4" | |
| 3 | 2' 7 1/4" | |
| 4 | 3' 11 1/4" | |
| 5 | 5' 3 1/4" | |
| 6 | 6' 7 1/4" | |
| 7 | 7' 11 1/4" | |
| 8 | 9' 3 1/4" | |
| 9 | 10' 7 1/4" | |
| 10 | 11' 11 1/4" | |
| 11 | 13' 3 1/4" | |
| 12 | 14' 7 1/4" | |
| 13 | 15' 11 1/4" | |
| 14 | 17' 3 1/4" | |
| 15 | 18' 7 1/4" | |
| 16 | 19' 11 1/4" | |
| 17 | 21' 3 1/4" | |
| 18 | 22' 7 1/4" | |
| 19 | 23' 11 1/4" | |
| 20 | 25' 3 1/4" | |
| 21 | 26' 7 1/4" | |
| 22 | 27' 11 1/4" | |
| 23 | 29' 3 1/4" | |
| 24 | 30' 7 1/4" | |
| 25 | 31' 11 1/4" | |
| 26 | 33' 3 1/4" | |
| 27 | 34' 7 1/4" | |
| 28 | 35' 11 1/4" | |
| 29 | 37' 3 1/4" | |
| 30 | 38' 7 1/4" | |
| 31 | end | 39' 10 1/2" |
Lumber: nominal to actual
Enter actual finished sizes in every tool. A nominal 2x4 is cut and dressed to the size shown.
| Nominal | Actual |
|---|---|
| 1x2 | 3/4" x 1 1/2" |
| 1x3 | 3/4" x 2 1/2" |
| 1x4 | 3/4" x 3 1/2" |
| 1x6 | 3/4" x 5 1/2" |
| 1x8 | 3/4" x 7 1/4" |
| 1x10 | 3/4" x 9 1/4" |
| 1x12 | 3/4" x 11 1/4" |
| 2x2 | 1 1/2" x 1 1/2" |
| 2x3 | 1 1/2" x 2 1/2" |
| 2x4 | 1 1/2" x 3 1/2" |
| 2x6 | 1 1/2" x 5 1/2" |
| 2x8 | 1 1/2" x 7 1/4" |
| 2x10 | 1 1/2" x 9 1/4" |
| 2x12 | 1 1/2" x 11 1/4" |
| 4x4 | 3 1/2" x 3 1/2" |
| 4x6 | 3 1/2" x 5 1/2" |
| 6x6 | 5 1/2" x 5 1/2" |
The link carries every input, so it opens the same calculation on a phone.