Hip roof
Equal pitch all round, hips at 45° in plan. Birdsmouth and plumb cut templates for the commons are in the common rafter calculator.
Commons and ridge
- Roof angle8:12 pitch
- 33.69°
- Runhalf the width, to the ridge centre
- 12' 0"
- Rise
- 8' 0"
- Common line length14' 5 1/16" to the ridge centre less 7/8" for the ridge
- 14' 4 3/16"
- Common overalltail 1' 9 5/8" for 1' 6" overhang
- 16' 1 13/16"
- Common plumb cutseat 56.31°, heel 2 5/16", HAP 6 3/8"
- 33.69° · 8 11/16"
- Ridgehip centre to hip centre; board 16' 1 1/2" (plus one common thickness), top 8' 6 3/8" above the plate
- 16' 0"
Hip rafters
- Hip angle8:12 per 17 (16.97) of run
- 25.24°
- Hip runin plan, corner to the ridge centre
- 16' 11 5/8"
- Hip line length18' 9 1/8" to the ridge centre less 1 3/16" (1 1/16" level)
- 18' 7 15/16"
- Hip overalltail 2' 4 1/8"
- 21' 1/8"
- Hip plumb cutseat 64.76° · 8 15/16", heel 4 3/16"
- 25.24° · 10 1/4"
- Hip cheek cutfrom square on the top edge, both ways to a point at the ridge
- 42.13°
- Hip dropdeepen the seat so the edges meet the roof planes; HAP 6" after the drop
- 3/8"
- Hip capall four hips, eave to ridge
- 84' 5 1/8"
Jacks, counts and materials
- Jack diminisheach jack is this much longer than the last at 16" centers
- 1' 7 1/4"
- Jack cheek cutfrom square on the top edge; plumb cut same as the common
- 39.76°
- Jack shorteninghalf the hip's 45° thickness, 1 1/16" level
- 1 1/4"
- Rafters28 commons, 64 jacks (8 per hip per face), 4 hips
- 96
- Roof areasides 478.64 sq ft each, ends 219.04 sq ft each
- 1395.35 sq ft
- Sheathing30 per side face, 20 per end face, no waste allowance
- 100 sheets
- Lumber$910.80 at $800 per 1000 bft
- 1138.5 bft
| # | From corner | To hip centre | Cut length |
|---|---|---|---|
| 1 | 1' 4" | 1' 7 1/4" | 1' 5 15/16" |
| 2 | 2' 8" | 3' 2 7/16" | 3' 1 3/16" |
| 3 | 4' 0" | 4' 9 11/16" | 4' 8 7/16" |
| 4 | 5' 4" | 6' 4 15/16" | 6' 3 5/8" |
| 5 | 6' 8" | 8' 1/8" | 7' 10 7/8" |
| 6 | 8' 0" | 9' 7 3/8" | 9' 6 1/8" |
| 7 | 9' 4" | 11' 2 5/8" | 11' 1 5/16" |
| 8 | 10' 8" | 12' 9 13/16" | 12' 8 9/16" |
Jack lengths are from the plumb line at the outer wall to the hip, long point of the cheek; add the common tail for the overhang. The same jacks occur on all four corners and both faces.
Framing plan
Hip roof framing plan
Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.
CommonsJacksHipsJacks are numbered from the corner along the near wall.
Hip rafter
Hip rafter
Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.
Drop or backing
Square section through the hip. Dropping lowers the whole hip by deepening the seat so its top corners meet the roof planes; backing bevels the top edge instead and keeps the full height above plate.
Hip drop and backing
Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.
Hip plumb cut template
Mark the plumb line at 25.24° from square on the hip's face, then the cheek cuts from the top edge.
Hip plumb cut
Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.
Jack cheek cut template
Top edge view. Lay a jack's top edge on the drawing with its long point at the square line and mark the cheek; the plumb cut below it is the common's.
Jack cheek cut
Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.
Hip cheek cut template
The hip is cut both ways from the centre of its top edge to meet the ridge and the two king commons.
Hip cheek cut
Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.
| # | Mark | Position |
|---|---|---|
| 1 | jack | 1' 4" |
| 2 | jack | 2' 8" |
| 3 | jack | 4' 0" |
| 4 | jack | 5' 4" |
| 5 | jack | 6' 8" |
| 6 | jack | 8' 0" |
| 7 | jack | 9' 4" |
| 8 | jack | 10' 8" |
| 9 | common | 12' 0" |
| 10 | common | 13' 4" |
| 11 | common | 14' 8" |
| 12 | common | 16' 0" |
| 13 | common | 17' 4" |
| 14 | common | 18' 8" |
| 15 | common | 20' 0" |
| 16 | common | 21' 4" |
| 17 | common | 22' 8" |
| 18 | common | 24' 0" |
| 19 | common | 25' 4" |
| 20 | common | 26' 8" |
| 21 | common | 28' 0" |
| 22 | jack | 29' 4" |
| 23 | jack | 30' 8" |
| 24 | jack | 32' 0" |
| 25 | jack | 33' 4" |
| 26 | jack | 34' 8" |
| 27 | jack | 36' 0" |
| 28 | jack | 37' 4" |
| 29 | jack | 38' 8" |
Lumber
| Item | Pieces | Stock length | Board feet | Cost |
|---|---|---|---|---|
| Common rafters | 28 | 18' 0" | 456.8 | $365.40 |
| Hip rafters | 4 | 22' 0" | 101.8 | $81.40 |
| Jack rafters | 40 | 16' 0" | 580.0 | $464.00 |
Jacks are paired long with short out of one stock length where they fit. Ridge, fascia, hip and ridge caps are reported as lengths above.
Lumber: nominal to actual
Enter actual finished sizes in every tool. A nominal 2x4 is cut and dressed to the size shown.
| Nominal | Actual |
|---|---|
| 1x2 | 3/4" x 1 1/2" |
| 1x3 | 3/4" x 2 1/2" |
| 1x4 | 3/4" x 3 1/2" |
| 1x6 | 3/4" x 5 1/2" |
| 1x8 | 3/4" x 7 1/4" |
| 1x10 | 3/4" x 9 1/4" |
| 1x12 | 3/4" x 11 1/4" |
| 2x2 | 1 1/2" x 1 1/2" |
| 2x3 | 1 1/2" x 2 1/2" |
| 2x4 | 1 1/2" x 3 1/2" |
| 2x6 | 1 1/2" x 5 1/2" |
| 2x8 | 1 1/2" x 7 1/4" |
| 2x10 | 1 1/2" x 9 1/4" |
| 2x12 | 1 1/2" x 11 1/4" |
| 4x4 | 3 1/2" x 3 1/2" |
| 4x6 | 3 1/2" x 5 1/2" |
| 6x6 | 5 1/2" x 5 1/2" |